Due to the particularity of the use of diesel generator set (it is generated by the kinetic energy generated by the high-speed rotation of the engine, which is converted into electric energy through the excitation of the generator), the machinery will generate a certain amount of heat during movement. At this time, the heat needs to be dissipated through cooling. Therefore, the generator set is generally cooled by fan water tank, so as to ensure that all mechanical parts of the generator set can be within a certain temperature control range.

但是，發電機組在使用過程中，經常會產生水箱溫度過高，導致柴油機缸體過高，達到一定的溫度時會自動停機（這是因為發電機組上裝有水高溫自動保護功能），如果機組上沒有帶有自動保護功能，那么會隨著發動機的溫度越來越高，發動機的缸體的溫度也越來越高，潤滑油的潤滑效果會越來越差，損傷發動機缸體，那么，這個發電機組的水箱溫度高是由什么引起的呢，下面，鋒發動力為您詳細分析發電機組水溫過高的原因：

However, during the use of the generator set, the temperature of the water tank is often too high, resulting in the high temperature of the diesel engine cylinder block. When it reaches a certain temperature, it will shut down automatically (this is because the generator set is equipped with the automatic protection function of water high temperature). If the generator set is not equipped with the automatic protection function, the temperature of the engine cylinder block will be higher and higher as the engine temperature is higher and higher, and the lubrication effect of the lubricating oil will be worse and worse, If the engine block is damaged, what causes the high temperature of the water tank of the generator set? Below, Fengfa power will analyze the reasons for the high water temperature of the generator set in detail:

一、是噴油時間過早或過遲屬，影響燃燒過程，引起補燃期過長，使冷卻水接觸氣缸壁的時間相對延長，造成水溫過高，這個一般是根據柴油機的不同，它的噴油時間不同，正常的發動機都不會存在這樣的問題，除非機器收過損傷。

1、 The reason is that the injection time is too early or too late, which affects the combustion process, causes the supplementary combustion period to be too long, relatively prolongs the time for the cooling water to contact the cylinder wall, and causes the water temperature to be too high. This is generally based on the brand of diesel engine and its injection time. Such a problem will not exist in normal engines unless the machine is damaged.

二、是噴油量過大，造成混合氣過濃，緩燃期、補燃期相應延長，而使水溫過高。這個可能是由于突然加負載，或者突然加大油門造成

2、 The reason is that the fuel injection quantity is too large, resulting in too rich mixture, correspondingly prolonging the slow combustion period and supplementary combustion period, resulting in too high water temperature. This may be caused by sudden loading or sudden increase of throttle

三、是噴油器噴油壓力過高或過低，使燃油的噴射行程和霧化質量受到影響。噴油壓力過高，噴在燃燒 室壁上的柴油形成液態，不利于霧化險為夷噴油壓力低，霧化質量差。噴油器滴油使供油量大，引起水溫過高，嚴重時使噴油器燃損。

3、 The fuel injection pressure of the fuel injector is too high or too low, which affects the injection stroke and atomization quality of the fuel. If the injection pressure is too high, the diesel injected on the combustion chamber wall forms a liquid, which is not conducive to atomization. The injection pressure is low and the atomization quality is poor. The fuel injector drips oil to make the fuel supply large, which causes the water temperature to be too high, and in serious cases, the fuel injector burns out.

四、是配氣相位失準，使氣缸在壓縮終了時壓縮壓力降低；進氣不充分，延長了緩燃期和補燃期，引起水溫過高。進氣系統堵塞也會使混合氣體過濃，發動機冒黑煙，動力下降，水溫過高。氣門和氣門座圈磨損，活塞和缸套磨損均使壓縮力降低，引起燃燒不良也使水溫過高，動力性能下降。

4、 It is the misalignment of valve phase, which reduces the compression pressure of the cylinder at the end of compression; Insufficient air intake prolongs the slow combustion period and supplementary combustion period, resulting in too high water temperature. The blockage of the intake system will also make the mixture too thick, the engine emits black smoke, the power drops and the water temperature is too high. The wear of valve and valve seat ring, piston and cylinder liner reduce the compression force, cause poor combustion, make the water temperature too high and reduce the power performance.

五、是散熱器堵塞、水垢過多及風扇膠帶松等均會造成水溫過高。水泵壓力低，流量小，使冷卻液循環速度慳，從而造成水溫過高。需要定期清洗水箱，更換冷卻液

5、 It is that the radiator is blocked, too much scale and the fan tape is loose, which will cause the water temperature to be too high. The low pressure and small flow of the water pump make the coolant circulation speed low, resulting in high water temperature. The water tank needs to be cleaned regularly and the coolant needs to be replaced

六、是發動機內部零部件之間摩擦阻力大，潤滑條件不好，排氣管或消間器堵塞，發動機負荷過大等也會造成水溫過高的現象。檢查使用的潤滑油的油品及質量。

6、 High friction resistance between internal parts of the engine, poor lubrication conditions, blocked exhaust pipe or eliminator, excessive engine load and so on will also cause the phenomenon of too high water temperature. Check the oil and quality of the lubricating oil used.

以上就是為大家介紹的有關190發電機組配件的詳細的介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以專業的態度,為您提供服務http://blmhz.com

The above is a detailed introduction to the accessories of 190 generator set. I hope it will be helpful to you If you have any questions, please contact us We will provide you with professional service http://blmhz.com